- Drivetrain Weight
- Chassis Strength
- Wheel Capacity
- Problems with Robot Turning
- IFI Wheel Tread Attachment
- Keyed Wheel Hubs for IFI Traction Wheels
- Control System Overview Document
- Upgrading RC and OI
- 2005 Documentation
- 2005 Power Distribution Drawing
- Operator Interface Users Manual
- Joysticks and the Joystick Port
- Tether Port
- Practice Channels
- Power On LED
- 1 Joystick Drive Code
- Select Button
- Dashboard OI/RC Jumper
- Radio Channels
- Competition Port
- Upgrades
- No Data/Radio LED
- LEDs Driven from Relay Ports
- Loose Power Terminals
- Bluetooth to Serial Adapter
- Analog Inputs
- Device Reader and Dynamic Debug
- Disable and Autonomous
- Low Voltage from PWM Outputs
- Using the CCP modules to capture edges
- Using VEX Servos
- Battery and Power ON/OFF
- PWM Outputs 13-16
- Connecting Sensor
- Baud Rate
- Reversed analog inputs to the EDU Controller
- Program Port Pin-out
- Program Button
- Digital I/O
- TTL Serial Port
- Getting data while disabled, then Autonomous
- Program Port Y-Cable
- Autonomous (No Operator Interface required)
- Uploading from the Robot Controller
- Programming - Program Button - Program State LED
- Interrupts
- PWM Ouput
- Program Port and Program State LED
- Reset/Prog Pins
- Radio Port
- Team Color Connector
- Cables and Wiring
- LCD Character Display
- 2007 Radio Modems
- "No Data/Radio" is blinking on the RC, OI
- 900MHz modem to WIFI compatability
- Radio Channels
- Older Radios
- Victor Overview
- Forward versus Reverse
- Output Steps
- Dead-Band
- An adjustable current source
- Two Thors Driving One Motor
- Fan Clearance
- Monitor Supply
- Feedback
- Circuit Breakers
- No LED
- Input Signal
- PWM Cable does not fit
- Brake/Coast Switching
- PWM-DRIVER Cable
- PWM Current
- Intermittent Loss
- Victor Lag
- Flashing Red
- Calibration
- Motors turn in wrong direction
- Victor 884 Problem
- Speed Controller Connections
- Input Update Rate
- 1 Victor for 2 motors
- Spike Overview
- Back EMF
- Wiring a Compressor
- Exceeding 20 Amps
- Control a Motor
- Spike and the Mini-RC
- Indicator Lights
- What is the older "Red" Spike?
- Dashboard Viewer Overview
- Dasboard Port Overview
- Data Stream Spec
- OI or RC Data
- Pocket PC Compatible
- Dashboard to RC
- Moding bits
- Programming the Robot Controller
- Help! I don’t know how to program C! What can I do?
- Which registers/modules/functions are off limits?
- Packet Number
- Timer Modules and Counters
- Code Size
- Delays
- RC Master Code
- Change voltage to Motor
- 2005 Default Code
- Autonomous
- Generate_PWMs()
- Project File
- PicSerialdrv.c
- Operating Systems for MPLAB® and IFI Loader
- I/O Pin Mapping
- MPLAB® Files
- Program Size Limits
- Code Simulation
- Interrupts
- printf
- Can I perform trig functions (like sin, cos, tan)?
- Can I use floating-point numbers in my program?
- Assembly Programming
- Can I use a Microchip programming device like the ICD 2?
- Programming Cable
- Master Code Upgrade
- IFI_Loader
- Downloading 2006 code into the 2005 Controller
- Error Code
- MPLAB IDE and IFI Loader locations
- Controller Verification says TALOS
- FrcCode.hex verse FRC_default.hex
- USB to Serial
- Dynamic Debug Tool
- New Firmware or Default Code
- Program State LED
- Where are the Macintosh versions of MPLAB® and IFI Loader?
- Compilation Errors
- Error - not enough parameters
- PID Library Routines
- Library Changes
- How can I return my robot to the default functionality?
- Broken Spade Connector
- Center Connector
- USB chicklet problems
- USB-Chicklet