1. 2 months ago

    _qui

    May 15 Russellville, AR 967A

    For the caps, do you guys plan to grab it on the core or the long flat sections?

    I would say that the best way to manipulate the cap is grabbing along the wider point(not the core) and having a mechanism turn the cap 180 degrees and lift up to the lower or higher post or just turn it and put it on it's side. The problem with that is that the caps won't always have the core touching the field so we also need to devise a way to grab a cap at nearly any angle efficiently.

  2. I would say that the best way to manipulate the cap is grabbing along the wider point(not the core) and having a mechanism turn the cap 180 degrees and lift up to the lower or higher post or just turn it and put it on it's side. The problem with that is that the caps won't always have the core touching the field so we also need to devise a way to grab a cap at nearly any angle efficiently.

  3. @turningPoint I would say that the best way to manipulate the cap is grabbing along the wider point(not the core) and having a mechanism turn the cap 180 degrees and lift up to the lower or higher post or just turn it and put it on it's side. The problem with that is that the caps won't always have the core touching the field so we also need to devise a way to grab a cap at nearly any angle efficiently.

    I might be wrong, but I think the caps are designed to self right them self when they are leaning on their edge. Not when they are standing on their edge, though.

  4. Korbin

    May 15 99402

    I try to think of ideas outside of what other people are doing just so I can have some freedom in the design process for at least the early season, and an idea that I've had since the game was released was a mold to fit around the core, twisting it forwards and backwards with 360 degree capability, this way you'd be able to pick up tilted caps and simply flip them.

    I've yet to make a protoype of this since I have end-of-the-year exams and all but when I do, I don't expect to see perfection.

  5. _qui

    May 15 Russellville, AR 967A

    @turningPoint I would say that the best way to manipulate the cap is grabbing along the wider point(not the core) and having a mechanism turn the cap 180 degrees and lift up to the lower or higher post or just turn it and put it on it's side. The problem with that is that the caps won't always have the core touching the field so we also need to devise a way to grab a cap at nearly any angle efficiently.

    Exactly our thinking with the 180 degree turning device

  6. _qui

    May 15 Russellville, AR 967A

    @Impulse Theory I might be wrong, but I think the caps are designed to self right them self when they are leaning on their edge. Not when they are standing on their edge, though.

    I believe that this is correct

  7. JairMeza20

    May 15 Rhode Island 1784

    For early season, a simple fork can work well. The fork could be made of axels or standoffs and can be used to pick up, place down, and even flip over. I think a more flushed out intake could be something like a friction fit passive intake that holds the cap parallel to the ground and can turn over with a motor. This could be helpful for a. accuracy when placing and picking it up, and b. can quickly turn over caps on the high posts faster than a purely passive intake. I think my team might be doing something where the intake comes over the top of the cap, and gets pushed down into it. The cap is held in place with something that has a good amount of friction like tape or something.

  8. I think fork. Also with grip they would work very well.

  9. RougeScaless

    May 16 Bangkok 2979A, 2979C, 2979E

    @375X Robotics How are you going to flip it with a fork? Do you want two sides?

  10. JamsG

    May 16 a place in southern california 310A

    this isn't my picture or idea and i forgot which person posted it so i'm sorry about
    that

    32260786_242233586340590_4895497096569815040_n.png

    but claws that can grab caps by the top of the core should be able to passively flip over caps if put on some freely rotating axle/screw

  11. Edited 2 months ago by Alex241N

    Has anyone thought of a 2:1 chain bar design yet? Caps only need to be in one of two positions: red up or blue up.
    Building a simple chain bar lift would allow scoring from either side of the robot, depending on how far you rotate the bar. This would save on the extra complexity of an additional system, as well as the (possible) motor such a system would (possibly) require.

    What @JamsG suggests is definitely a cool idea, though. Just remember that if that is an active system claw, wire management may turn out to be a nightmare.

  12. 8232X

    May 16 NH 8232X

    @Alex241N Are you competing again this year? I haven't seen you this active in a while.

    Back on topic, I have been thinking that grabbing by the outer section (not the core) with some way to flip them, either left-right or front-back. That way your "fork" doesn't have to be 6" long to reach the core safely.

  13. briancole

    May 16 Utah 4270C

    Has anyone though of not using a claw? I mean, there weren't mobile goal claws in itz, and caps rest on the ground in a relatively similar way.

  14. JamsG

    May 16 a place in southern california 310A

    @Alex241N What @JamsG suggests is definitely a cool idea, though. Just remember that if that is an active system claw, wire management may turn out to be a nightmare.

    Well if the wire twists one way enough, eventually it will have to go the other way ;)

  15. @JamsG Well if the wire twists one way enough, eventually it will have to go the other way ;)

    It's your life on the line when you ask your Coach for a new motor :D

  16. @8232X @Alex241N Are you competing again this year? I haven't seen you this active in a while.

    Back on topic, I have been thinking that grabbing by the outer section (not the core) with some way to flip them, either left-right or front-back. That way your "fork" doesn't have to be 6" long to reach the core safely.

    No, though I do wish I had the time. I'm just a little too far away from it all.

  17. Riptide

    May 16 Canton, Michigan 21636A

    @briancole Has anyone though of not using a claw? I mean, there weren't mobile goal claws in itz, and caps rest on the ground in a relatively similar way.

  18. Riptide

    May 16 Canton, Michigan 21636A

    The insanely good dr4b doesn't use a claw.

  19. Mark Finley

    May 16 Las Vegas, Nevada 6891B

    @JamsG this isn't my picture or idea and i forgot which person posted it so i'm sorry about
    that

    but claws that can grab caps by the top of the core should be able to passively flip over caps if put on some freely rotating axle/screw

    I was thinking about this and it could also be done this way probably more reliably, but it would take a motor.

  20. JamsG

    May 17 a place in southern california 310A

    @Mark Finley I was thinking about this and it could also be done this way probably more reliably, but it would take a motor.

    the problem with slotting those c-channel onto the cap's edges like that is trying to pick up caps that are slanted on the ground. if a cap was in a corner and slanted, i think it would be pretty difficult to move the caps out

  21. Newer ›
 

or Sign Up to reply!